Kia Rio: Body Electrical System / Button Engine Start System

Components and components location

Schematic diagrams

Description and operation

System Overview

The System offers the following features:

The RKE and SMART KEY functions are not considered part of this Button Engine Start system and are specified in a separate system.

System Main Function

Button Engine Start System

The Button Start System allows the driver to operate the vehicle by simply pressing a button (called as SSB) instead of using a standard mechanical key.

If the driver presses the SSB while prerequisites on brakes, fob authentication and transmission status are satisfied, the BES System will proceed with the locking/unlocking of the steering column, the control of the terminal, and the cranking of the engine.

The driver can release the SSB as soon as this sequence is initiated. After positive response from immobilizer interrogation, the system will activate the starter motor and communicate with the EMS to check the engine running status for starter release.

The driver will be able to stop the engine by a short push on the SSB if the vehicle is already in standstill. Emergency engine stop will be possible by a long press of the SSB or 3 consecutive presses in case the vehicle is in ENGINE RUNNING.

If the conditions for engine cranking are not satisfied while a push on the SSB is detected and a valid fob authenticated, the system will unlock the steering column and switch the terminals to IGN. Another push on the SSB will be necessary to start the engine.

In case of a vehicle equipped with SMART KEY system, fob authentication will not require any action from the driver. For limp home start or in case of vehicle without SMART KEY, the driver will have to insert the fob into the fob holder.

Indicator ON/OFF Condition At Ignition Key Off Condition

Indicator ON/OFF Condition According To Ignition Key's Position

Operation for each function of button starting

Limp home mode

Smart Key Unit

The SMK manages all function related to:

The smart key unit masters the entire button engine start system.

In case of SMART KEY application, for example "Passive Access”, "Passive Locking” and "Passive Authorization are integrated for Terminal switching Operations”.

It collects information about vehicle status from other modules (vehicle speed, alarm status, driver door open...), reads the inputs (e.g. SSB, Capacitive Sensor / Lock Button, PARK position Switch), controls the outputs (e.g. exterior and interior antennas), and communicates with others devices via the CAN network as well as a single-line interfaces.

The diagnosis and learning of the components of the BES System are also handled by the SMK.

The SMK manages the functions related to the "terminal control" by activating external relays for ACC, IGN1 and IGN2. This unit is also responsible for the control of the STARTER relay.

The SMK is also controlling the illumination of the SSB as well as the "system status indicator", which consists of 2 LEDs of different color. The illumination of the fob holder is also managed by the SMK.

The SMK reads the inputs (Engine fob in, vehicle speed, relays contact status), controls the outputs (Engine relay output drive), and communicates with others devices via the CAN.

The internal architecture of the SMK is defined in a way that the control of the terminal is secured even in case of failure of one of the two microcontrollers, system inconsistency or interruption of communication on the CAN network.

In case of failure of one of the two controllers, the remaining controller shall disable the starter relay. The IGN1 and IGN2 terminals relays shall be maintained in the state previously memorized before the failure and the driver shall be able to switch those IGN terminals off by pressing the SSB with EMERGENCY_STOP pressing sequence. However, engine restart will not be allowed. The state of the ACC relay will depend on the type of failure.

The main functions of the SMK are:

Start/Stop Button (SSB)

A single stage push button is used for the driver to operate the vehicle. Pressing this button allows:

The contact will be insured by a micro-switch and a backlighting is provided to highlight the marking of the button whenever necessary.

Three (3) LED colors are located in the outside ring of the switch assy. They display the status of the system.

They are OFF(White) / ACC(Amber) / ON(Green).

BES(Button Engine Start) System State Chart

System STATES in LEARNING MODE

In learning mode, the BES System can be set in 6 different states, depending on the status of the terminals and Engine status:

Referring to the terminals, the system states described in the table above are the same as those found in a system based on a mechanical ignition switch.

One of the features distinctive from the Mechanical Ignition Switch-based system is that the BES system allows specific transition from [OFF] to [START] without going through [ACC] and [IGN] states.

System STATES IN VIRGIN MODE

The BES System can be set in 5 different states (OFF LOCKED is not available in virgin mode), depending on the status of the terminals and Engine status :

Referring to the terminals, the system states described in the table above are the same as those found in a system based on a mechanical ignition switch.

One of the features distinctive from the Mechanical Ignition Switch-based system is that the BES system allows specific transition from [OFF] to [START] without going through [ACC] and [IGN] states.

• Start/Stop Button
• ESCL(Electronic Steering Column Lock)